Gtechniq Crystal Serum

Gtechniq Crystal Serum
Brand: Gtechniq
Product Code: GQ-CS30
Availability: Out Of Stock
Price: $0.00
Ex Tax: $0.00
Qty:  
   - OR -   
Crystal Serum’s innovative composite ceramic structure represents a major development in aftermarket covalently bonding ultra durable nano-coatings.  
 
A single application of Crystal Serum not only forms a thicker protective barrier than standard nano-coats it also offers independently proven class leading levels of gloss, scratch and chemical resistance and durability.
 
Crystal Serum can be applied either as a stand-alone product or for the ultimate in hydrophobic function it can be overcoated with Gtechniq EXOv2 or C2v3.
 
Application instructions Crystal Serum
  • Prepare your surface by removing any contaminants and or polish residues as this will ensure the highest density of cross-links between Crystal Serum and the surface of the vehicle.  For this we recommend using Gtechniq Panel Wipe and a Gtechniq MF1 ZeroR Microfibre Buff Cloth.
  • Ensure that there is no risk of water dripping onto partially cured coating from trim parts or seals.  For this we recommend using an air line to blow any excess water from these areas. (if water does drip onto partially cured coating we recommend repolishing the affected area and reapplying Crystal Serum).
  • Make sure the surface you are working on is cool, dry and out of direct sunlight (panels should be between 5oc and 30oc)
  • When applying the product always wear latex gloves to prevent the product coming into contact with your skin.
  • Dab plenty of product onto the application pad.
  • Replace the lid on the bottle and set aside (do not keep the bottle in your hand as this promotes premature curing).
  • Spread the coating over an area no larger than half a small panel or quarter of a large panel.
  • The coating forms an almost immediate reaction with the surface of the vehicle so you should immediately remove residue with a Gtechniq MF1 ZeroR Microfibre Buff Cloth.
  • You may need to buff the same area several times to fully remove residues for which we recommend using two microfiber cloths at any one time.  
  • Please note that you are only removing excess product so avoid buffing with too much force as this can marr softer paint finishes.
  • For ease of spotting surface residue we recommend using a medium intensity flat light source (high intensity spot lights as used to spot paint defects are not recommended) and angling your head so that you view each surface from several oblique angels.
  • Take care that the microfiber cloths you are using are rotated sufficiently quickly so that Crystal Serum doesn’t partially cure in the cloth as this will make buffing residue significantly more difficult.
  • We also recommend joining edges of coated areas “wet to wet” (ie if you are doing the roof do one side and the other side immediately afterwards).
  • If you miss removing residue and it cures fully you will need to carefully wet sand the affected panel, repolish and then reapply Crystal Serum as unlike C1 Crystal Lacquer or EXO you cannot remove the fully cured film with a cutting compound.
  • We recommend the vehicle stays dry for at least 12 hours post application.
  • We do not recommend layering Crystal Serum with a further layer of Crystal Serum but for improved hydrophobic function, Crystal Serum can be layered with two coats of Gtechniq EXOv2 (allow 3 hours before applying EXO over Crystal Serum).
  • Immediately machine wash used MF1 cloths after use but we advise not to use the same cloths again 

*This Product is only for Professional application and only authorized detailer can apply. Not Available to Public. Please email chuan@maxdetail.co.nz if interestered.

 

 

 

 

 

Write a review

Your Name:


Your Review: Note: HTML is not translated!

Rating: Bad           Good

Enter the code in the box below:



Tags:
Powered By OpenCart
Maximum Detail © 2018